Do you know all the precautions for lamp installation?

Release date: 2017-12-13Source : Red jade lighting sharing:

1. When installing the lamp, if you install the sub-control switch, you can save a lot of troubles. Because if there is only one main switch, and several lights are on and off, you can't choose the light and darkness of the light, and it will waste power. With the sub-control switch, you can choose to turn on a few lights at any time. If there is an aisle at the entrance of the house, it is best to install a switch at the end of the aisle so that the power can be turned off directly after entering the door, without having to go back to the door to turn off the lights.

2, the lighting system should be set to be adjustable, that is, when the light is dim or glare, you can make adjustments, people will feel more comfortable and more comfortable.

3. The color temperature of the light should be consistent with the atmosphere of the living room, at least to the color temperature of other areas of the living room. Lights can be installed on the top floor to reduce shadows during work.

4. Do not install a single lighting source in the center. For kitchen lighting, a multi-level lighting system consisting of different lamps and light sources should be installed in the kitchen.

5. The installation location is also very important. Straight incandescent or fluorescent lamps should be mounted towards the front of the cabinet. In this way, part of the light from the lamp is directed at the tailgate and then reflected onto the console and then towards the center of the space.

6. If the space is high enough, a transparent or translucent chandelier can be installed on the ceiling as a light source. The chandelier can not only provide excellent illumination, but also a good decorative item.

7, the installation of the lamp, the most important thing is to be firm, you can use a hand to pull it, feel it.

8. The bottom cover of the lamp should be close to the ceiling and cannot be shaken.

9. If it is a chandelier, there will be a wire extending from the top to the base of the lamp. It should be noted that this wire cannot be taut. It should be loosely wrapped around the tie rod, otherwise the long-term tight wire is easy. Something went wrong.

10. Check carefully that there should be no wires exposed outside.

11. In addition, many ceiling lamps have scratch-resistant membranes. They need to be removed after installation. Anyone who knows it is very difficult. In fact, there is a small trick. You can blow this film with a hair dryer and then expose it. It can be easily removed.

How to supervise the installation of lamps

1. Use the springboard to set up on the full frame of the civil construction. Install from the edge of the full frame. Each time a springboard is installed, the springboard must be fixed on the full frame with the saddle hoop so that the springboard will not move. The springboard crosses the full frame. All must be fixed so that one section is followed by a section to form a channel.

2. Before the workers work, the construction workers should carefully inspect the safety protection articles such as seat belts. They believe that the safety belts must be fastened when there is no safety hazard. All activities in non-work areas such as smoking and play are prohibited during the operation. Workers should use the tool bag for the springboard work. After the tool is used, it must be placed in the tool bag. It is strictly forbidden to throw tools and other items.

3. The wiring of the welding machine should be one machine and one gate. It is strictly forbidden to pull the wires. The outer casing of the welder must be well protected to zero or ground. The installation and disassembly of the power supply should be carried out by an electrician. Welding personnel should be certified to work, and unlicensed operation is strictly prohibited. Personal protective equipment must be inspected and worn before welding. It is strictly forbidden to operate after drinking or emotionally unstable people.

4. The welding operation should be completed in the firework approval procedure three days in advance, and the inflammable and explosive materials should be removed around the welding site, or covered or isolated. There must be a guardian on site and a fire extinguisher.

5. When changing the site to move the wire, the power should be cut off. The welder does not entangle the wire to avoid serious heat and danger.

6. After the welding work is finished, the power of the welding machine should be cut off, and the operating point should be checked to confirm that there is no fire hazard before leaving.

7. The job site must be coordinated and commanded by professional construction workers and safety personnel on site. After the operation is completed, it is necessary to clean up the job site in time, so that the work is completed.

Label: lamps wholesale lamps join the lamps and lanterns purchase billion lamp network

AC Permanent Magnet Synchronous Motor

Kassel AC permanent magnet synchronous motor, also known as Ac Servo Motor. It is a motion control auxiliary equipment that is widely used in robots, CNC machine tools, printing and packaging, laser cutting, logistics automation, medical care, and new energy fields. It has the characteristics of compact structure, easy installation, complete flexibility, high torque, good reactivity and significantly improved safety.

Ac Permanent Magnet Synchronous Motor,Permanent Magnet Synchronous Ac Motor,Ac Synchronous Permanent-Magnet Electric Motor,Ac Permanent Magnet Synchronous Motor Kit

Kassel Machinery (zhejiang) Co., Ltd. , https://www.kasselservo.com