Human glutaminase (GluAP) enzyme-linked immunosorbent assay kit
Experimental operation
This kit is for research use only.
Experimental principle
This kit uses the double antibody sandwich method to determine the level of human glutaminase (GluAP) in the specimen. The microplate was coated with purified human glutaminase (GluAP) antibody to prepare a solid phase antibody, and glutaminase (GluAP) was sequentially added to the microcapsules of the coated monoclonal antibody, followed by the HRP-labeled valley. The aminoglycanase (GluAP) antibody binds to form an antibody-antigen-enzyme-labeled antibody complex, which is thoroughly washed and then added to the substrate TMB for color development. TMB is converted to blue under the catalysis of HRP enzyme and converted to the final yellow color by the action of an acid. The color depth is positively correlated with glutaminase (GluAP) in the sample. The absorbance (OD value) was measured with a microplate reader at a wavelength of 450 nm, and the concentration of human glutaminase (GluAP) in the sample was calculated from a standard curve.
Human glutaminase (GluAP) enzyme-linked immunosorbent assay kit
composition
130 times concentrated washing solution 20ml × 1 bottle 7 stop solution 6ml × 1 bottle
2 enzyme standard reagent 6ml × 1 bottle 8 standard (960pg / ml) 0.5ml × 1 bottle
3 enzyme label coating plate 12 holes × 8 9 standard dilutions 1.5ml × 1 bottle
4 sample dilution 6ml × 1 bottle 10 instructions 1 copy
5 color developing agent A liquid 6ml × 1 bottle 11 sealing film 2 sheets
6 color developer B liquid 6ml × 1 bottle 12 sealed bag 1
Specimen requirements
1. The specimens should be extracted as soon as possible after collection, and the extraction should be carried out according to the relevant literature. The experiment should be carried out as soon as possible after extraction. If the test cannot be performed immediately, the specimen can be stored at -20 °C, but repeated freezing and thawing should be avoided.
2. Samples containing NaN3 could not be detected because NaN3 inhibited horseradish peroxidase (HRP) activity.
Human glutaminase (GluAP) enzyme-linked immunosorbent assay kit
Steps
1. Dilution of standard: This kit provides one original standard, which can be diluted in a small tube according to the following chart.
150μl standard dilution of 150μl standard sample of 480pg/ml No.5 standard
Add 150 μl of standard dilution to the standard No. 5 of 240 μg/ml No. 4 standard 150 μl
120pg/ml No. 3 standard 150μl of No. 4 standard added 150μl standard dilution
60pg/ml No. 2 standard 150μl of No. 3 standard added 150μl standard dilution
Add 30 μl standard dilution of 150 μl standard No. 1 of 30 pg/ml No. 1 standard
2. Loading: Set blank holes separately (the blank control wells are not added with the sample and the enzyme standard reagent, the other steps are the same), the standard holes, and the sample holes to be tested. Accurately load 50 μl of the standard on the enzyme-labeled plate, add 40 μl of the sample dilution to the well to be tested, and then add 10 μl of the sample to be tested (the final dilution of the sample is 5 times). Add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, and shake gently to mix.
3. Incubation: The plate was sealed with a sealing film and incubated at 37 ° C for 30 minutes.
4. Dosing: 30 times (20 times of 48T) concentrated washing solution diluted with distilled water 30 times and used
5. Washing: Carefully remove the sealing film, discard the liquid, dry it, fill each well with the washing liquid, let stand for 30 seconds, then discard it, repeat 5 times, and pat dry.
6. Add enzyme: 50 μl of enzyme labeling reagent was added to each well, except for blank wells.
7. Incubation: The operation is the same as 3.
8. Washing: The operation is the same as 5.
9. Color development: Add 50 μl of the developer to each well, then add 50 μl of the developer, gently shake and mix, and develop at 37 ° C for 10 minutes.
10. Termination: 50 μl of stop solution was added to each well to terminate the reaction (when the blue color turned yellow).
11. Measurement: The absorbance (OD value) of each well was measured sequentially with a blank air conditioner of zero and a wavelength of 450 nm. The measurement should be carried out within 15 minutes after the addition of the stop solution.
Calculation
Taking the concentration of the standard as the abscissa and the OD as the ordinate, draw a standard curve on the coordinate paper, and find the corresponding concentration from the standard curve according to the OD value of the sample; multiply by the dilution factor; or use the concentration of the standard Calculate the linear regression equation of the standard curve with the OD value, substitute the OD value of the sample into the equation, calculate the sample concentration, and multiply by the dilution factor, which is the actual concentration of the sample.
Human glutaminase (GluAP) enzyme-linked immunosorbent assay kit
Precautions
1. The kit should be taken out from the refrigerated environment and should be used at room temperature for 15-30 minutes before use. If the enzyme label is unsealed after opening, the slats should be stored in a sealed bag.
2. Concentrated washing liquid may crystallize out. When diluted, it can be heated and dissolved in a water bath. The washing will not affect the result.
3. The sampler should be used for each step, and the accuracy should be corrected frequently to avoid test errors. It is best to control the loading time within 5 minutes. If the number of specimens is large, it is recommended to use a gun.
4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the substance to be tested in the specimen is too high (the OD value of the sample is larger than the OD value of the first hole of the standard well), please first dilute the sample dilution with a certain multiple (n times) and then measure it. When calculating, multiply the total dilution by the total dilution. Multiple (×n×5).
5. The sealing film is intended for single use only to avoid cross-contamination.
6. Please keep the substrate away from light.
7. strictly follow
Human glutaminase (GluAP) enzyme-linked immunosorbent kit
The operation is carried out, and the test results must be determined by the microplate reader reading.
8. All samples, washings and various wastes should be treated as infectious materials.
9. The different batch components of this reagent must not be mixed.
Storage conditions and expiration date
1. Kit storage: 2-8 ° C.
2. Validity: 6 months
ZGAR FIT
ZGAR electronic cigarette uses high-tech R&D, food grade disposable pod device and high-quality raw material. All package designs are Original IP. Our designer team is from Hong Kong. We have very high requirements for product quality, flavors taste and packaging design. The E-liquid is imported, materials are food grade, and assembly plant is medical-grade dust-free workshops.
From production to packaging, the whole system of tracking, efficient and orderly process, achieving daily efficient output. We pay attention to the details of each process control. The first class dust-free production workshop has passed the GMP food and drug production standard certification, ensuring quality and safety. We choose the products with a traceability system, which can not only effectively track and trace all kinds of data, but also ensure good product quality.
We offer best price, high quality Vape Device, E-Cigarette Vape Pen, Disposable Device Vape,Vape Pen Atomizer, Electronic cigarette to all over the world.
Much Better Vaping Experience!
ZGAR FIT E-Cigarette Vape Pen,ZGAR FIT Device Vape,ZGAR FIT Vape Pen Atomizer,ZGAR FIT Disposable E-Cigarette OEM vape pen,ZGAR FIT electronic cigarette
Zgar International (M) SDN BHD , https://www.zgarvapepen.com