FANUC 7 system
The FANUC 7 system includes two series, 7 T and 7 M. Among them, 7 T system is suitable for two-coordinate CNC lathes, and 7 M is suitable for three-coordinate milling machines, boring and milling machines and machining centers. The 7 M system is taken as an example to illustrate its working principle.
1. System hardware structure
7 M takes the central processing unit (CPU) as the core. The CPU is connected to the memory and various interfaces through the bus. The overall block diagram is shown in Figure 3-51.
Figure 3-51 7M CNC system general block diagram
2. FANUC 7 system software structure
The system software of the 7 M CNC device is composed of a 22 K control program (20 K for the three-coordinate two-coordinated system), a 4 K CRT control program and a diagnostic program (input by a dedicated diagnostic paper tape).
The main function of the initialization program is to prepare for the normal work of the entire system. After booting, the "current status" of the "level 6 interrupt" is placed in the "current status register" through the "initialization microprogram" so that interrupts other than the level 7 interrupt cannot interrupt the initialization. At the same time, during the execution phase of the "initialization microprogram", the program is transferred to the "initialization program". Therefore, the "initialization program" is executed first after each boot. After entering the initialization program, the system puts the first address of the protection area of ​​the 0th level interrupt into the first address of the 6th level of the protection area, which causes the 6th level to interrupt the state of the 0th level, so that the initialization returns to the 0th level Level interrupt.
The initialization procedure mainly completes the following three tasks:
(1) Set the initial state for the unit in RAM as a working register.
(2) Perform ROM parity check.
(3) Set some required initial states for NC machining to proceed normally. Belonging to this initial state setting are part program memory area setting, AS area initial setting, and so on. Perform the necessary initial processing on some parameters set by the TE sub-mode (setting parameters). For example, the value of the rapid feed rate is converted from mm / min to um / 8ms. If you press some specific keys while turning on the machine, you can also perform additional operations.
3. Examples of parts processing
Now let's discuss the processing of parts. The processing of the first piece of a new part in the 7M system can be roughly described by the flow shown in Figure 3-58. For the first piece of a new part, it is generally necessary to observe the correctness of the programming through dry run. If there is a mistake, it can be corrected by editing the part program. After the first piece is processed, if the program needs to be saved, it can be worn as a paper tape for later use. Generally speaking, parts program editing and paper output work are not necessary when reprocessing the same kind of parts.
If you are new to the concept of using an electric kettle, you might be overwhelmed by the variety of electric kettles that are displayed on the store shelves and have difficulty deciding which one would be the best to suit your individual needs or desires. This introduction will give you some basic information about some of the features that are available on various types of electric kettles so that you can make a more informed decision when choosing one for use in your home.
Features:
Spend few minutes to boil : After 5 minutes, hot water will finish for you to drink.
3 protection functions : The on/off button is on the handle, making it easy to turn the kettle off when you pick it up. A concealed heating unit reduces the amount of buildup in the kettle.
It will be a problem when you forget to close the button.Once the water boils the kettle shuts itself off.Do not have to worry about damaging it by letting it run dry. When water runs dry,It will cut the electric by itself.
Multiple Cups: Water can be loaded to 1.8Liter.
Materials :
Food grade stainless steel, more healthy and hygienic. PP handle wieh heat insulation material provides scald resistance. Durable controller performance with 360 degree rotation cordless base design.
OEM & ODM service : Try best to support you during production and provide better after-sales service.Enhance your brand popularity.
Application:
Make a cup of tea.
Boil eggs.
Cook noodles.
Electric Water Kettle
Electric Water Kettle,Aluminium Electric Water Kettle,Mini Electric Water Kettle,Stainless Steel Electric Water Kettle
Guangzhou Taipeng Electrical Appliances Technology CO., LTD. , https://www.taipengelectric.com